Transition Networks SISTM10XX-162-LR Manual de usuario

SISTM10xx-162-LR(T) (6) 10/100Base-TX + (2) 100Base-FX Industrial Managed Switch Installation Manual

5 OFF Disable port Alarm 5 ON Enable port Alarm. If the port’s link fails, the fault LED will light up OFF Disable port Alarm 6 ON Enable port Alar

6 Off No power inputs Yellow Power failure or UTP port failure or Fiber port failure Fault Off No Power failure or UTP port failure or Fiber port fa

7 All ports on this industrial switch support automatic MDI/MDI-X operation, user can use straight-through cables (See figure below) for all network

8 Cabling • Using four twisted-pair, Category 5 cabling for RJ-45 port connection. The cable between the converter and the link partner (sw

9 Wiring the Fault Alarm Contact The fault alarm contact is in the middle of terminal block connector as below figure shows. By inserting the wires

10 Mounting Installation DIN-Rail Mounting The DIN-Rail is screwed on the industrial switch when out of factory. 1. First, insert the top of DI

11 3. Check the DIN-Rail is tightly on the track. 4. To remove the industrial switch from the track, reverse steps above. Wall Mount Plate Mount

12 Hardware Installation Installation Steps 1. Unpacking the Industrial switch 2. Check the DIN-Rail is screwed on the Industrial switch. If the

13 Network Application This chapter provides some sample applications to help user to have more actual idea of industrial switch function applicati

14 X-Ring Application The industrial switch supports the X-Ring protocol that can help the network system to recovery from network connection failur

Notice This manual contents are based on the below table listing software kernel version, hardware version, and firmware version. If the switch fun

15 Coupling Ring Application In the network, it may have more than one X-Ring group. By using the coupling ring function can connect each

16 Web-Based Management About Web-based Management On CPU board of the switch there is an embedded HTML web site residing in flash memory, which o

17 Home Interface Port status View every port status that depended on user’s setting and the negotiation result • Port: The port number • T

18 Single Port Information Click the port on the Panel figure on the web interface directly. Then, the single port information window will show up a

19 Port Control Change the port status • Select the port by scroll the Port column • State: Disable or enable control of this port • Negotiation

20 • Hardware version: Display the switch hardware version • MAC Address: Display the unique hardware address assigned by manufacturer (default)

21 Port Mirroring interface [NOTE] 1. Select the monitor mode as disable to disable the mirroring 2. Remember to execute the “Save Configuratio

22 VLAN Configuration interface Port-based VLAN Packets can go among only members of the same VLAN group. Note all unselected ports are treated a

23 • Click Add to add a new VLAN group(The maximum VLAN group is up to 64 VLAN groups) • Entering the VLAN name, group ID and grouping the members

24 802.1Q VLAN Tagged-based VLAN is an IEEE 802.1Q specification standard which it allows to create a VLAN across devices from different switch vend

Contents Notice...

25 • Grouping the ports and click Add button 802.1q VLAN –Add interface • And then, click Next then follow interface as below.

26  Click Apply to set the outgoing frames are VLAN-Tagged frames or untagged  Tag: Outgoing frames with VLAN-Tagged  Untag: Outgoing frames w

27 Alert There are three kinds of alert – e-mail, event, and power alarm for user to configure. Email Alert Configuration When the specific events

28 Event Configuration The selected events that occur will send out the alert to the assigned SMTP server. Also, user can select port events for a

29 Power Alarm Configuration Power alarm function enables the Relay alarm action. Without enabling power alarm function, the Relay alar

30 IP configuration interface SNTP Configuration User can configure the SNTP (Simple Network Time Protocol) settings. The SNTP allows

31 MEWT - Middle European Winter SWT - Swedish Winter EET - Eastern European, USSR Zone 1 +2 hours 2 pm BT - Baghdad, USSR Zone 2 +3 hours 3 pm

32 IP Security IP security function allows user to assign 10 specific IP addresses that have permission to access the switch through the web brows

33 System Configuration • User can view spanning tree information about the Root Bridge • User can modify RSTP state. After modification, click Ap

34 RSTP– System Configuration Interface Per Port Configuration Configure path cost and priority of every port • Select the port in Port column

Port status... 17 Sin

35 RSTP – Per Port Configuration interface X-Ring X-Ring provides a faster redundant recovery than Spanning Tree topology. The action is similar

36 The system also supports the coupling ring that can connect 2 or more X-Ring group for the redundant backup function and dual homing function tha

37 QoS Configuration Configure Qos setting of the every port • Oos Policy: Select the Qos policy rule  Using the 8,4,2,1 weight fair queue scheme

38 QoS configuration Interface IGMP The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP

39 Message Description Query A message sent from the querier (IGMP router or switch) asking for a response from each host belonging to the multicast

40 4. And then, click Apply Security Manager interface [NOTE] Remember to execute the “Save Configuration” action, otherwise the new configuratio

41 System Options • Name: Enter a name for the switch • Location: Enter the switch physical location • Contact: Enter the name of contact person

42 TFTP Restore Configuration interface TFTP Backup Configuration User can save current flash ROM value from the industrial switch to the TFTP s

43 • And then, click Apply TFTP Update Firmware interface Factory Default Reset Switch to default configuration. Except the IP address,

44 Save Configuration Save the industrial switch configuration to the flash memory. Power off the industrial switch without the saving, all changed

Save Configuration ... 44 Rate Cont

45 Rate Control Interface [NOTE] 1. Remember to execute the “Save Configuration” action, otherwise the new configuration will lose when switch pow

46 System Log Configuration interface Event Configuration User can select the system log events. When selected events occur, the system will send

47 • After selected, click Apply Event Configuration interface

48 Troubles shooting • Verify that is using the right power cord/adapter (DC 12-48V), please don’t use the power adapter with DC output bigger tha

49 Technical Specification Standard IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX and 100Base-FX Fast Ethernet IEEE802.3x Flow Control and Ba

50 Packet filter 4 types of packet filter rule with different packet combination:  All of packet  Broadcast/ multicast/ unknown unicast packet  Br

51 Spanning tree IEEE802.1d spanning tree IEEE802.1w rapid spanning tree. IGMP IGMP v1 and Query mode Up to 256 groups. SMTP Support SNTP to synch

52 Case Dimension IP-30, 54 mm (W) x 135 mm (H) x 105mm (D) EMI FCC Class A, CE EN61000-4-2 (ESD), CE EN61000-4-3 (RS), CE EN-61000-4-4 (EFT), CE

1 Introduction The SISTM10xx-162-LRx Managed Industrial Switch is a cost-effective solution and meets the high reliability requirements demanded by

2 Package Contents Please refer to the package content list below to verify them against the checklist. • SISTM10xx-162-LRx Managed Industrial Swit

3 Hardware Description In this paragraph, it will describe the Industrial switch’s hardware spec, port, cabling information, and wiring installatio

4 set all configurations back to default setting Bottom View The bottom view of the switch is shown below: DIP-switch The switch provides th