Transition-networks SISPM1040-182D Manual de usuario Pagina 129
- Pagina / 157
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Transition Networks SISPM1040-182D
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Appendix A—RJ-45 Pin Assignment
RJ-45 Pin Assignments
The UTP/STP ports will automatically sense for Fast Ethernet (10Base-T/100Base-TX
connections), or Gigabit Ethernet (10Base-T/100Base-TX/1000Base-T connections).
Auto MDI/MDIX means that the switch can connect to another switch or workstation
without changing straight through or crossover cabling. See the figures below for straight
through and crossover cable schematic.
10 /100BASE-TX Pin outs
With10/100BASE-TX cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6
for receiving data.
RJ-45 Pin Assignments
Pin Number Assignment
1 Tx+
2 Tx-
3 Rx+
6 Rx-
[NOTE] “+” and “-” signs represent the polarity of the wires that make up each wire pair.
The table below shows the 10/100BASE-TX MDI and MDI-X port pin outs.
Pin Number MDI-X Signal Name MDI Signal Name
1 Receive Data plus (RD+) Transmit Data plus (TD+)
2 Receive Data minus (RD-) Transmit Data minus (TD-)
3 Transmit Data plus (TD+) Receive Data plus (RD+)
6 Transmit Data minus (TD-) Receive Data minus (RD-)
- User Manual 1
- SISPM1040-182D 1
- Revision History 2
- FCC Warning 4
- CE Mark Warning 4
- Content 5
- Chapter 1 Introduction 9
- Stability Testing 12
- IEC60068-2-6 (Vibration) 12
- 1.2 Software Features 13
- 1.3 Package Contents 16
- 2.1 Physical Dimension 17
- 2.2 Front Panel 17
- 2.3 Bottom View 18
- 2.4 LED Indicators 19
- 3.1 Installation Steps 21
- 3.2 DIN-Rail Mounting 22
- 3.4 Wiring the Power Inputs 25
- 3.6 Cabling 27
- Transceiver Inserted 28
- Remove LC connector 30
- 4.1 X-Ring Application 33
- 4.3 Dual Homing Application 35
- 4.4 Dual Ring Application 36
- Chapter 5 Console Management 37
- Console login interface 39
- 5.4 CLI Management 40
- 5.5 Commands Level 40
- 6.3 System Login 43
- 6.4 System Information 44
- 6.5 IP Configuration 45
- IP configuration interface 46
- 6.6 DHCP Server 47
- 6.6.1 System configuration 48
- 6.6.2 Client Entries 49
- 6.6.3 Port and IP Bindings 50
- 6.7 TFTP 51
- 6.7.2 Restore Configuration 52
- 6.7.3 Backup Configuration 53
- 6.8 System Event Log 54
- SMTP Configuration interface 57
- 6.9 Fault Relay Alarm 60
- 6.10 SNTP Configuration 61
- SNTP Configuration interface 64
- 6.11 IP Security 65
- IP Security interface 66
- 6.12 User Authentication 67
- 6.13 Port Statistics 68
- Port Statistics interface 69
- 6.14 Port Control 70
- Port Control interface 71
- 6.15 Port Trunk 72
- 6.15.3 State Activity 80
- State Activity of Switch 2 81
- 6.16 Port Mirroring 82
- 6.17 Rate Limiting 83
- And then, click 84
- to apply the settings 84
- 6.18 VLAN configuration 85
- 6.18.1 Port-based VLAN 86
- 6.18.2 802.1Q VLAN 89
- 802.1Q Configuration 90
- Group Configuration 92
- 6.19 Rapid Spanning Tree 95
- 6.19.2 Port Configuration 97
- 6.20 SNMP Configuration 99
- 6.20.2 Trap Configuration 101
- 6.20.3 SNMPV3 Configuration 102
- 6.21 QoS Configuration 105
- 6.21.2 Port-based Priority 106
- 6.21.3 COS Configuration 107
- 6.21.4 TOS Configuration 107
- 6.22 IGMP Configuration 108
- IGMP Configuration interface 109
- 6.23 X-Ring 110
- X-ring Interface 111
- 6.24 LLDP Configuration 113
- 6.25.1 System Configuration 114
- 6.25.2 Port Configuration 116
- 6.25.3 Misc Configuration 117
- 6.26 MAC Address Table 118
- 6.26.2 MAC Filtering 120
- 6.26.3 All MAC Addresses 121
- 6.27 Power over Ethernet 123
- 6.28 Factory Default 125
- 6.29 Save Configuration 126
- 6.30 System Reboot 127
- Troubles shooting 128
- RJ-45 Pin Assignments 129
- Cross over cable schematic 130
- Cross over cables schematic 131
- RJ-45 Pin Assignment of PoE 132
- Appendix B—Command Sets 134
- Halt and perform a cold 135
- Port Commands Set 136
- Trunk Commands Set 139
- VLAN Commands Set 140
- Spanning Tree Commands Set 142
- QOS Commands Set 145
- IGMP Commands Set 146
- SNMP Commands Set 147
- Port Mirroring Commands Set 150
- 802.1x Commands Set 150
- TFTP Commands Set 153
- SNTP Commands Set 155
- X-ring Commands Set 156
Relacionado con productos y manuales para Accesorios De Computador Transition-networks SISPM1040-182D
(12 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.905 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales