Transition-networks SISPM1040-182D Manual de usuario descargar pdf (Pagina 25)

Transition Networks SISPM1040-182D

Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

3.4 Wiring the Power Inputs

Please follow the steps below to insert the power wire.

1. Insert AC or DC power wires into the contacts 1 and 2 for power 1, or 5 and 6 for

power 2.

2. Tighten the wire-clamp screws.

[NOTE]

The wire gauge should be in the range 12 ~ 24 AWG.

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 156 157

User Manual 1
SISPM1040-182D 1
Revision History 2
FCC Warning 4
CE Mark Warning 4
Content 5
Chapter 1 Introduction 9
Stability Testing 12
IEC60068-2-6 (Vibration) 12
1.2 Software Features 13
1.3 Package Contents 16
2.1 Physical Dimension 17
2.2 Front Panel 17
2.3 Bottom View 18
2.4 LED Indicators 19
3.1 Installation Steps 21
3.2 DIN-Rail Mounting 22
3.4 Wiring the Power Inputs 25
3.6 Cabling 27
Transceiver Inserted 28
Remove LC connector 30
4.1 X-Ring Application 33
4.3 Dual Homing Application 35
4.4 Dual Ring Application 36
Chapter 5 Console Management 37
Console login interface 39
5.4 CLI Management 40
5.5 Commands Level 40
6.3 System Login 43
6.4 System Information 44
6.5 IP Configuration 45
IP configuration interface 46
6.6 DHCP Server 47
6.6.1 System configuration 48
6.6.2 Client Entries 49
6.6.3 Port and IP Bindings 50
6.7 TFTP 51
6.7.2 Restore Configuration 52
6.7.3 Backup Configuration 53
6.8 System Event Log 54
SMTP Configuration interface 57
6.9 Fault Relay Alarm 60
6.10 SNTP Configuration 61
SNTP Configuration interface 64
6.11 IP Security 65
IP Security interface 66
6.12 User Authentication 67
6.13 Port Statistics 68
Port Statistics interface 69
6.14 Port Control 70
Port Control interface 71
6.15 Port Trunk 72
6.15.3 State Activity 80
State Activity of Switch 2 81
6.16 Port Mirroring 82
6.17 Rate Limiting 83
 And then, click 84
to apply the settings 84
6.18 VLAN configuration 85
6.18.1 Port-based VLAN 86
6.18.2 802.1Q VLAN 89
802.1Q Configuration 90
Group Configuration 92
6.19 Rapid Spanning Tree 95
6.19.2 Port Configuration 97
6.20 SNMP Configuration 99
6.20.2 Trap Configuration 101
6.20.3 SNMPV3 Configuration 102
6.21 QoS Configuration 105
6.21.2 Port-based Priority 106
6.21.3 COS Configuration 107
6.21.4 TOS Configuration 107
6.22 IGMP Configuration 108
IGMP Configuration interface 109
6.23 X-Ring 110
X-ring Interface 111
6.24 LLDP Configuration 113
6.25.1 System Configuration 114
6.25.2 Port Configuration 116
6.25.3 Misc Configuration 117
6.26 MAC Address Table 118
6.26.2 MAC Filtering 120
6.26.3 All MAC Addresses 121
6.27 Power over Ethernet 123
6.28 Factory Default 125
6.29 Save Configuration 126
6.30 System Reboot 127
Troubles shooting 128
RJ-45 Pin Assignments 129
Cross over cable schematic 130
Cross over cables schematic 131
RJ-45 Pin Assignment of PoE 132
Appendix B—Command Sets 134
Halt and perform a cold 135
Port Commands Set 136
Trunk Commands Set 139
VLAN Commands Set 140
Spanning Tree Commands Set 142
QOS Commands Set 145
IGMP Commands Set 146
SNMP Commands Set 147
Port Mirroring Commands Set 150
802.1x Commands Set 150
TFTP Commands Set 153
SNTP Commands Set 155
X-ring Commands Set 156

Comentarios a estos manuales

Sin comentarios

Transition-networks SISPM1040-182D Manual de usuario Pagina 25

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios De Computador Transition-networks SISPM1040-182D