Transition-networks SISPM1040-182D Manual de usuario Pagina 137
- Pagina / 157
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
129
duplex
[full | half]
I Use the duplex
configuration
command to specify
the duplex mode of
operation for Fast
Ethernet.
switch(config)#interface
fastEthernet 2
switch(config-if)#duplex full
speed
[10|100|1000|auto]
I
Use the speed
configuration
command to specify
the speed mode of
operation for Fast
Ethernet., the speed
can’t be set to 1000 if
the port isn’t a giga
port..
switch(config)#interface
fastEthernet 2
switch(config-if)#speed 100
no flowcontrol I
Disable flow control of
interface
switch(config-if)#no flowcontrol
security enable I
Enable security of
interface
switch(config)#interface
fastEthernet 2
switch(config-if)#security enable
no security I
Disable security of
interface
switch(config)#interface
fastEthernet 2
switch(config-if)#no security
bandwidth type all I
Set interface ingress
limit frame type to
“accept all frame”
switch(config)#interface
fastEthernet 2
switch(config-if)#bandwidth type
all
bandwidth type
broadcast-multicast-
flooded-unicast
I Set interface ingress
limit frame type to
“accept broadcast,
multicast, and flooded
unicast frame”
switch(config)#interface
fastEthernet 2
switch(config-if)#bandwidth type
broadcast-multicast-flooded-
unicast
- User Manual 1
- SISPM1040-182D 1
- Revision History 2
- FCC Warning 4
- CE Mark Warning 4
- Content 5
- Chapter 1 Introduction 9
- Stability Testing 12
- IEC60068-2-6 (Vibration) 12
- 1.2 Software Features 13
- 1.3 Package Contents 16
- 2.1 Physical Dimension 17
- 2.2 Front Panel 17
- 2.3 Bottom View 18
- 2.4 LED Indicators 19
- 3.1 Installation Steps 21
- 3.2 DIN-Rail Mounting 22
- 3.4 Wiring the Power Inputs 25
- 3.6 Cabling 27
- Transceiver Inserted 28
- Remove LC connector 30
- 4.1 X-Ring Application 33
- 4.3 Dual Homing Application 35
- 4.4 Dual Ring Application 36
- Chapter 5 Console Management 37
- Console login interface 39
- 5.4 CLI Management 40
- 5.5 Commands Level 40
- 6.3 System Login 43
- 6.4 System Information 44
- 6.5 IP Configuration 45
- IP configuration interface 46
- 6.6 DHCP Server 47
- 6.6.1 System configuration 48
- 6.6.2 Client Entries 49
- 6.6.3 Port and IP Bindings 50
- 6.7 TFTP 51
- 6.7.2 Restore Configuration 52
- 6.7.3 Backup Configuration 53
- 6.8 System Event Log 54
- SMTP Configuration interface 57
- 6.9 Fault Relay Alarm 60
- 6.10 SNTP Configuration 61
- SNTP Configuration interface 64
- 6.11 IP Security 65
- IP Security interface 66
- 6.12 User Authentication 67
- 6.13 Port Statistics 68
- Port Statistics interface 69
- 6.14 Port Control 70
- Port Control interface 71
- 6.15 Port Trunk 72
- 6.15.3 State Activity 80
- State Activity of Switch 2 81
- 6.16 Port Mirroring 82
- 6.17 Rate Limiting 83
- And then, click 84
- to apply the settings 84
- 6.18 VLAN configuration 85
- 6.18.1 Port-based VLAN 86
- 6.18.2 802.1Q VLAN 89
- 802.1Q Configuration 90
- Group Configuration 92
- 6.19 Rapid Spanning Tree 95
- 6.19.2 Port Configuration 97
- 6.20 SNMP Configuration 99
- 6.20.2 Trap Configuration 101
- 6.20.3 SNMPV3 Configuration 102
- 6.21 QoS Configuration 105
- 6.21.2 Port-based Priority 106
- 6.21.3 COS Configuration 107
- 6.21.4 TOS Configuration 107
- 6.22 IGMP Configuration 108
- IGMP Configuration interface 109
- 6.23 X-Ring 110
- X-ring Interface 111
- 6.24 LLDP Configuration 113
- 6.25.1 System Configuration 114
- 6.25.2 Port Configuration 116
- 6.25.3 Misc Configuration 117
- 6.26 MAC Address Table 118
- 6.26.2 MAC Filtering 120
- 6.26.3 All MAC Addresses 121
- 6.27 Power over Ethernet 123
- 6.28 Factory Default 125
- 6.29 Save Configuration 126
- 6.30 System Reboot 127
- Troubles shooting 128
- RJ-45 Pin Assignments 129
- Cross over cable schematic 130
- Cross over cables schematic 131
- RJ-45 Pin Assignment of PoE 132
- Appendix B—Command Sets 134
- Halt and perform a cold 135
- Port Commands Set 136
- Trunk Commands Set 139
- VLAN Commands Set 140
- Spanning Tree Commands Set 142
- QOS Commands Set 145
- IGMP Commands Set 146
- SNMP Commands Set 147
- Port Mirroring Commands Set 150
- 802.1x Commands Set 150
- TFTP Commands Set 153
- SNTP Commands Set 155
- X-ring Commands Set 156
Relacionado con productos y manuales para Accesorios De Computador Transition-networks SISPM1040-182D
(12 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.119 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales